进口高压不锈钢电磁阀   铝业设备用电磁阀

LIPDGARF高压不锈钢电磁阀

LIPDGARF pressure solenoid valve

   LIPDGARF高压不锈钢电磁阀铝业设备用电磁阀作为自动控制及远程控制的一个执行器，它广泛应用在铝业、冶金、石化、轻纺、制药、食品、烟草、国防、科研等各项领域，其流通的介质分别为蒸汽、空气、油、水、燃气、制冷剂等。

   LIPDGARF pressure solenoid valve as an automatic control and a remote control actuator, it is widely used in the field of metallurgy, petrochemical, textile, pharmaceutical, food, tobacco, defense, scientific research, its circulation media are steam, air, oil, water, gas, refrigerants.

铝业设备用电磁阀工作原理working principle：

   当线圈通电，动铁芯吸合，先导阀口处于开启状态，使主阀塞上腔降压，主阀塞因压差开启，介质流通。当线圈断电，动铁芯复位，先导阀口处于关闭状态，使主阀塞上腔升压，将主阀塞压下，电磁阀关闭.

   When the coil is energized, the movable core pull, the pilot valve port is turned on, the main valve plug chamber pressure, because the pressure to open the main valve plug, medium flow. When the coil power, moving core reset, the pilot valve port is closed, the main valve plug chamber booster, the main valve plug depressed, the solenoid valve is closed.

技术参数Technical Parameters：

阀体材质：不锈钢304     压力等级：0-32.0mpa

使用温度：≤650°C     电源电压：AC220V   DC24V

结构型式：先导式       控制方式：常开、常闭

连接方式：NPT螺纹 、G螺纹    介质：水、油

Body material: stainless steel 304    Pressure rating: 0-32.0mpa

Temperature: ≤650°C    Power supply voltage: AC220V DC24V

Structure type: Pilot      Control: normally open, normally closed

Connection: NPT thread, G thread    medium: water, oil

安装维护Installation and maintenance：

1、现场安装必须按照国家防爆危险场所“电气安全规程”中有关规定进行。

2、电磁阀内外接地，必须牢固可靠。

3、电磁阀引出电缆导线为三根，其中一根为接地线，另二根为工作导线。

4、电磁阀安装前应将管路内部清洗干净。

5、电磁阀有杂质时，进口端前必须安装密度0.5mm的过滤器。

6、安装电磁阀时注意阀体上箭头要求与介质流向一致。

7、电磁阀应垂直安装，线圈在上。

8、电磁阀维修时应断电后开盖，非电器人员不得拆卸电磁阀电气部件。

1, on-site installation must be carried out in accordance with the national explosion-proof hazardous location "Electrical safety regulations" the relevant provisions.

2, the solenoid valve inside and outside the ground, must be solid and reliable.

3, the solenoid valve lead cable conductors for the three, which one is the ground wire, and the other two wires to work.

4, the solenoid valve is mounted inside the front line should be cleaned.

5, when the solenoid valve with impurities, must be installed before the inlet end of 0.5mm density filter.

6, pay attention to the arrow on the valve body in line with the medium flow requirements to install the solenoid valve.

7, the solenoid valve should be mounted vertically on the coil.

8, when the solenoid valve repair after opening the lid off, non-electrical personnel may not disassemble solenoid valve electrical components.

德国雷普阀门总代理：深圳派克阀门有限公司

Germany LIP valve distributor: Shenzhen Parker Valve Co.